In 3D
Snap Clip
Lightest wall or pegboard clip: push the grip in, it clicks; pull up to release.
- Fits
- BLOWZER X6 (TF-BZX6)
- Version
- 3
- Credit
- Designed by BLOWZER
Test status
Fit-checked digitally
Fit check in Blender: end cap rests on the shelf, bumps preload the grip rails ~0.4 mm (intended). READY-TO-PRINT/Confirmed/ (2026-09-21) holds this STL, read as an owner test print that fitted — no written verdict, so the status stays fit-checked-digitally until the owner confirms.
Awaiting the owner's confirmation as test-printed.
Downloads
blowzer-x6-snap-clip-v3.stl STL — mesh, ready to slice · 111 KB blowzer-x6-snap-clip-v3.step STEP — CAD, for designing · 1.1 MBDigital DIY files. Printed parts are not included in the retail BLOWZER box; you print and use them at your own discretion.
How to use it
A 70 × 90 plate with two flexible jaws that snap over the narrow ends of the grip, plus a shelf under the grip cap with the USB-C slot. Push in → click; lift or tilt forward to remove. Keyholes at 50 mm spacing. Print it in PETG so the jaws keep flexing.
Print settings
- Print orientation
- back plate (wall side) on the bed; jaws and shelf grow as vertical walls
- Material
- PETG (PLA works, flexes less)
- Supports
- none
- Layer height
- 0.2 mm
- Nozzle
- 0.4 mm
- Walls
- 3
- Infill
- 25–30 %
- Scale
- 100 % — do not scale, the grip pocket stops fitting
- Extra hardware
- 2 × #8 (4 mm) wall screws
- Size (as printed)
- 70 × 90 × 36 mm
- Filament
- ≈ 37 g PLA at 30 % infill
- Assembly
- Not specified
- Notes
- 2.4 mm jaws with 1.5 mm ramped snap bumps; ≈0.4 mm preload on the grip rails at rest.
Reuse terms
BLOWZER X6 Reference Model Licence (v1.1, 2026-10-02) Copyright (c) 2026 Sabrent. "BLOWZER" and "SABRENT" are trademarks of their owners. You may, free of charge, for personal AND commercial purposes: 1. Use, copy, measure and modify these reference files to design, test, make and SELL accessories, mounts, docks, holders, cases, adapters and similar add-ons that fit or work with the BLOWZER X6. 2. Include these files, unchanged or modified, in the published source of such an accessory, with this notice. You may NOT: 3. Use these files to reproduce, manufacture or sell the BLOWZER X6 product itself or a product that copies its housing, or imply that your accessory is made or endorsed by Sabrent. 4. Remove the BLOWZER / SABRENT marks from the model and present the result as a different product. The files are provided "as is", without warranty of any kind. Dimensions are taken from the factory CAD and the printed solid is a voxel reconstruction (see README) — verify critical fits against a real unit.
Version history
- v3 Sep 17, 2026 recessed BLOWzer X6 wordmark on the plate
- v2 Sep 17, 2026 1.5 mm ramped snap bumps at the jaw tips (engage 0.5 mm behind the grip corners)
- v1 Sep 17, 2026 1.0 mm square bumps engaged only 0.02 mm — superseded
Discussion
0 replies · 0 printed →Questions, fit reports and print logs live in the forum thread. Printed it? Post an "I printed this" reply there.